|
SPEC
2003 |
| Materials | |
| Mast pocket: | Teijin soft 375gm/m2. |
| Mast panel: | D/P 5 mil narrow grid Xply. |
| Foot panel: | Dimension/Polyant 5mil narrow grid Xply. |
| Boom panels: | D/P 5 mil narrow grid Xply lower, D/P 4 mil
wide grid Xply rear, 175 monofilm, forming together dual radial clew 2-plys. |
| Leech panels: |
D/P 5mil narrow grid Xply with dacron adhesive 2&3ply |
| Upper body panels: | 125 monofilm. |
| Head panels: |
D/P 4mil wide grid Xply with 175 mono 2ply under a Teijin dacron 3ply rear. |
| Foot: | D/P 5mil narrow grid Xply and Teijin dacron 2ply & 3ply & large vinyl edge finishing. |
| Hardware | |
| Head: | Fixed top all sizes. Heavy doubled 2.0cm ribbed webbing with
vinyl cover/protector, molded 2pc top cap & two wear rivits. |
| Clew: | 1.3cmID stainless eyelet. |
| Tack: | 1.8cmID stainless eyelet. |
| Battens: |
Bottom and top two: Pultruded 8mm polyester rods with specific ground double taper forward.
Above boom: Carbon tubes with pultruded 8mm polyester rods with specific ground double taper forward.
Sensitip: 6mm pultruded non-tapered polyester rod headbatten, autotensioning with downhaul design.
Microbattens:
Upper: 4mm pultruded non-tapered polyester rod.
Lower: 2.5mm pultruded non-tapered polyester rod. |
| Batten tensioners: | Stainless bolt in molded "rocket" with
Spectra loop, driver placed in sailbag.
|
| |
| Sail Weights |
Size
(m2) |
Weight
(kg) |
| 5.9 |
3.90 |
| 6.6 |
4.10 |
| 7.4 |
4.41 |
| 8.4 |
4.91 |
| 9.6 |
5.19 |
| 10.8 |
5.76 |
|
|
| Mast & Boom Specs
2003 O2 Freeride Concept |
|
Sail
Size
(m2) |
Mast
Length
(cm) |
Boom
Length
(cm) |
Recommended
Mast
(cm) |
Compatible
Masts |
|
5.9 |
447 |
188 |
430 |
430RDM, 460RDM, 460 |
|
6.6 |
470 |
201 |
460 |
460RDM, 430, 430RDM |
|
7,4 |
499 |
214 |
490 |
460, 460RDM |
|
8.4 |
529 |
226 |
520 |
490 |
|
9.6 |
557 |
254 |
550 |
|
|
10.8 |
572 |
262 |
550 |
|
|
5.9 vario top, all other sizes fixed top. |
2003
Series Colors
A: Red with Black
C: Blue with
White
B: Yellow with Black
D: White with Orange
Build Highlights
Seam protection from mast inside of mast
pocket.
Tack patch stitching protected with scrim dacron
tack patech covers, both sides.
Reinforcement patches
sewn into the mast pocket at batten pocket intersections, lower 3
battens.
Wear rivits on batten ends and mast pocket
top.
Inside the mast pocket on the bottom battens.
webbing covers are sewn over the batten pocket forward end
finishings to protect abrasion between the forward batten ends
and the mast.
50cm X 8mm thick closed cell foam mast/board
protector built into mast pocket bottom, velcro opening right
side.
Vinyl rienforced mast pocket top
cover.
Neoprene rear batten (bottom) end cover with
velcro closure and vinyl abrasion patch.
All
monofilm seams reinforced with glued on scrim
dacron.
Oversized soft vinyl finishing sewn onto the foot edge.
|